PageContent
Report of the activities of Centro di Elettronica Bologna presented to the Section Assembly – July 2022
Detail of activities by Group I
| ATLAS | Preparation and testing of fiber optic connection networks for the irradiation tests envisaged for the developments for runs 3 and 4 of the Lucid – Avoni detector | |
| ATLAS | ASupporto e maintenance per rivelatore Lucid: preprazione di nuove basi di PMT e disegno dei frontalini delle schede elettroniche – Avoni | |
| ATLAS | Bakelite resistivity measurement system for RPC detectors – Meneghini | |
| ATLAS | Preliminary design of the upgrade of the LUCROD board for the LUCID detector – Meneghini | |
| ATLAS | Support for the use of the LUCROD-ZDC board in the experiment – Meneghini | |
| ATLAS | Assembly and installation of 4 “IGAP and SENSORS patch panel” cards for the Muons detector – Avoni | |
| ATLAS | Wiring finalization and LGAD detector test for the BMA detector (beam monitor)- Avoni | |
| ATLAS | Technical support for the maintenance of Forward Detectors – Avoni | |
| ATLAS | Support assembly of detectors and preparation for beam tests for ZDC and RPD detectors – Avoni | |
| ATLAS | Support for reworking trigger cards for the Muons detector -Avoni | |
| ATLAS | Support and firmware development for the ROD board of the Pixel detector: implementation of embedded-Linux. creation of a “twin” setup in Bologna- Balbi | |
| ATLAS | Production of a new batch of LV_CUTOFF_BOARD boards for ITK sensor test setup – Torromeo | |
| ATLAS | Design of a circuit with different sensors for the ITK test setup in collaboration with the Lecce section – Veri | |
| ATLAS | Test support for soldering electronic components on RPC detectors – Pellegrini | |
| ATLAS | Production of HV_SWITCH BOX boards -Torromeo | |
| CMS | Design and implementation of a NIM – TTL – LVDS signal conversion board – Mastropasqua. – Zuffa | |
| CMS | Design and manufacture of LVFE boards – Zuffa | |
| CMS | Fast inference of Deep Learning models on FPGA resources – Travaglini | |
| LHCB | Firmware drawing on PCIe40 card for the acquisition of the PLUME detector – Balbi, Torromeo | |
| RD-FCC | Support for beam testing with microRwell detector – Falchieri | |
| SND@LHC | Production of the SND_SIPM60 board and commissioning at the experiment – Baldanza | |
| MUonE | Hardware, firmware and software support for the calorimeter acquisition system – Balbi. Baldanza. Falchieri. Travaglini | |
| LUXE | Design of a custom crate for the Gamma Beam Profile (GBP) detector reading system – Zuffa. Avoni | |
| LUXE | Support for the layout design and production of the electronic board for the GBP detector sensors and design of test boards- Zuffa | |
Detail of activities by Group II
| NU-AT-FNAL | Participation in the assembly and wiring of CRT detectors at Fermilab Pellegrini. – Degli Esposti |
| NU-AT-FNAL | Design and production of SiPM characterization boards for the Dune experiment: in Liquid-Argon (amplifier) and hot (150 front-end boards. Relay board) – Lax |
| NU-AT-FNAL | Design of SiPM matrix test boards for the GRAIN: Motherboard and mezzanine demonstrator- Lax |
| DarkSide | Design and production of OPTOLINK and PDUslim Differential TX boards – Zuffa |
| KM3 | Support to the Bologna site for the production of Base Modules: electronic assembly and testing – Pellegrini |
| KM3 | Support for the production of the Base Modules in the different sites (Catania and Caserta): preparation of the assembly kits. quality documentation. Production of the cables necessary for the entire production – Pellegrini |
| KM3 | Assembly and testing of a Calibration Unit – Pellegrini |
| KM3 | Support for design and prototype testing for phase 2 modules – Pellegrini |
| KM3 | Participation in the detector deployment campaign on the Italian site Pellegrini. – Degli Esposti |
| KM3 | Production of a new batch of GBoard boards and new Gboard Flex Extender circuits – Pellegrini |
| KM3 | Firmware development for the Octopaes board – Degli Esposti |
| Limadou | Assembly and wiring of 140 PRT2 circuits for HEPD detector PMTs – Lolli |
| Limadou | Test with the vacuum chamber of the PRT2 board section – Lolli |
| Limadou | PMT test and assembly for the HEPD detector – Lolli |
| ENUBET | Upgrade of the connections of the tracker previously made for the experiment – Nessie Degli Esposti |
| ENUBET | Design of the patch board for upgrading the connections of the Nessie tracker – Veri |
| CUORE | Control system maintenance and data taking – Lolli |
Detail of activities by Group III and V
| ALICE | Firmware development for DRM2 board for ALICE TOF for LHC RUN3 – Falchieri |
| ALICE | Progettazione PCB PicoTDC_adapterBoard – Torromeo |
| ALICE | Preliminary board design with PicoTDC and FPGA – Baldanza |
| EIC_NET | DAQ firmware development for 6 Alcor chip readout and support for two beam tests at CERN – Falchieri |
| EIC_NET | Design and manufacture of SiPM Carrier Extension flex cards – Baldanza |
| FAMU | High rate, low noise analog mezzanine PCB design for GSPS digitizer – Veri |
| FAMU | Firmware development and testing for the GSPS digitizer – Travaglini |
| FAMU | Fast Baseline Restorer board design and production – Zuffa |
| FAMU | Production of font-end boards for the LaBr3 detector and PMT HV divider – Zuffa |
| FOOT | Assembly of SiPM test circuits – Meneghini |
| FIRE | Realization of two versions of printed circuit called Patch Board – Veri |
| ARCADIA | Sfirmware development for MD1 + MD2 chip readout. support to users of other sections. participation in chip characterization sessions with sources / cosmics / lasers – Falchieri |
| ARCADIA | Participation in a working group for the design / verification of the final MD3 chip – Falchieri. Balbi |
Summary of activities (other projects and service management)
| VARIOUS | Support for radiofrequency irradiation system via TEM – Torromeo |
| MICROELECTRONICS | Study and maintenance of CAD and licenses – Falchieri. Balbi. Veri |
| MICROELECTRONICS | Training on wire bonding techniques (in collaboration with the Silici Laboratory) – Torromeo |
| TRAINING | Two internships with students of the Belluzzi-Fioravanti Technical Institute (PCTO) – Falchieri. Lolli |
| TRAINING | Course on programmable logic and Verilog language at the Technical Institute of Faenza (2 classes) – Balbi |
| TRAINING | Preparation of additional internship activities – Balbi. Bisi. Veri. Zuffa |
| MULTIMEDIA | Audio / video support for events. training courses and editing and filming archiving – Bisi Lolli Meneghini |
| DEVELOPMENT | FPGA firmware write learning – Baldanza. Degli Esposti. Veri |
| MANAGEMENT | Order Support All – [Zuffa > 40] |
| MANAGEMENT | Licensing support – Bisi |
| MANAGEMENT | Instrumentation management – Tutti |
| EEE | Test of the new production of Polar_FPGA cards – Meneghini |
| Fortress | External project – Support for the design of the boards for the front-end of reading flexible sensors- Torromeo. Travaglini |
| AIDA INNOVA MRPC | External project Support for the production of cathode cards – Meneghini |
| INTEFF-HIBRAD | External project Design. production and testing of the control board of the thermo-regulated cage – Lax |
| INTEFF-HIBRAD | External project Firmware of the microcontroller for the management of the thermoregulated cage – Lax. Mastropasqua |
